Dayboat/Launch 23 plan – trailer a cruising outboard boat


Video image can take a moment to load.

Dayboat Launch and Venezia are camp aboard Riverboat or Canal Boats that cruise efficiently under modest outboard motors and are constructed  from prefabricated plywood panels. This one with 10hp high thrust Yamaha.

Video shows ability in chop

23ft Dayboat Launch on Hawkesbury River
  • Flexible interior – Picnic boat, camp cruiser, comfortable
  • Cruiser, party boat.
  • Easily Trailerable, Enclosed toilet area.
  • Low power – high cruising speeds.
  • Recommend High Thrust Outboards for quiet and economic running

Boat Basic Stats

Length – 23ft (7m)
Beam – 6ft 6ins (1.98m)
Power – 10hp
Plans – $120 (was $250) for both this and the Venezia 27ft version. 

Contact an agent in the Top Right of any page or click here.

Also see these boats suitable for high thrust outboards.
Venezia – 27ft – larger version riverboat/canalboat for Venice Italy – space for permanent berths – included with this plan
Dayboat/Launch – alternative interior
TC35 – 35ft semi liveaboard

Dayboat launch riverboat restored by Drew Campbell

The Gorilla in the room is how do flat bottom boats handle a steep chop?

The answer is very well. If the waves are short, steep and close together they handle it brilliantly with no noise, no pitching and no loss of speed.

Check the last minute of the video at the top of this page. No pitching or lurching and good speed.


Origins of the outboard Dayboat Launch:

DAyboat Launch Picnic boat you can build yourself. 10hp high thrust outboard. Sleep or camp cruiser: storerboatplans.com

I was originally approached by a Sydney company called Shearwater Marine to draw up a Hire-and-Drive picnic boat for Sydney Harbour.  The idea was for a boat that could be built quickly in series production from prefabricated panels with a minimum of tooling.  It had to look cute compared to the opposition – companies hiring out aluminium dinghies with 6hp outboards.

The first Shearwater Marine boat floating in Elizabeth Bay, Sydney harbour Right.

Later the idea was to be expanded into a fleet of around 50 boats.

They would operate out of different hire businesses up and down the east coast on the plentiful rivers, lakes and estuaries. They looks like good “on the cheap” canal boats for Europe.

Shearwater Marine (Richard and Ken) would take care of the maintenance and repair by the simple expedient of having a couple of extra boats up their sleeves (so to speak).

When routine maintenance came up for one of the boats up the coast they would simply roll up with a replacement boat on a trailer and swap them over, the other to be refurbished in their factory.

Yep – Another boat design “get rich quick scheme” :)

For me as a designer it was another “get rich quick” scheme** – design one boat then get the royalty each time another riverboat was built – 50 boats times, say $200 each – looks quite good on paper.

** (yes, Another – see the story at the bottom of the Eureka Canoe page: “The boat that almost made us our fortune.”)

What is the slowest part of building a cruising outboard riverboat … or any boat?

Well, we succeeded on all grounds.  The boat went together quickly because of the prefabricated plywood panels with all major components made up on the flat (drawing right), looked quite handsome, behaved quite well in the water.

But the problem was the labour involved in painting all that surface area.

Simple hullshape of 23ft Dayboat Launch. See how pretty it turns out: storerboatplans.com

Despite the fact the riverboat was relatively clean and simple the labour estimates for the finishing made the whole 49 boat project uneconomic. Obviously painting one boat was fine – but another 49+ could drive you nuts!!!

It is a bit of a general lesson really – if someone says that a particular boat will take only 6 hours to build, or that their construction method takes half the time of someone else’s design then they are quite possibly not including the painting!

Hull Design, prefabricated plywood panels and what they owe to Phil Bolger

23ft Dayboat Launch on Hawkesbury River

As is probably obvious to knowledgeable readers the hullform and building method using prefabricated panels is a derivative of sharpie building methods. In particular those developed by American genius Phil Bolger.

His “State” class rivercruisers (named Tennessee, Idaho, Wyoming etc) are very light displacement and quite narrow, with beam to length at around 1:5.

Flexible interior – click this link for one Alternative Interior Layout (html)

DAyboat Launch Picnic boat you can build yourself. designed around prefabricated plywood panels. 10hp high thrust outboard. Sleep or camp cruiser: storerboatplans.com

The narrowness is essential to prevent the flat bottom from pounding.  One of the great experiences of my life was when the first Tennessee was launched in Adelaide.

I sat up on the bow watching fascinated while going into a short, sharp Murray River chop.

The bow did not pitch in the slightest, cutting each wave in turn.  Unlike the conventional bow boats around us a totally smooth ride. Not a drop of water aboard. Not a hint of pounding.

The original Hire and Drive Riverboat has undergone an awesome restoration in the last year.

Dayboat launch riverboat restored by Drew Campbell

Introducing the 27ft Version Riverboat or Launch

When buying the plans from Duckworks we include the extended version. Effectively it adds back the chopped off stern of the 23 footer. Interior is completely up to the builder and there is a structural requirement of a step through bulkhead in at least two places in builds.

See the 27ft Dayboat Launch information here.

Seakeeping within the constraints of riverboats or canal boats:

Such a dry comfortable ride in a short chop makes the boat a perfect
Murray River (or other major river) Rambler.

Video of the Dayboat in a wind against tide river chop shows no pitching and a comfortable quiet ride.

And these canal boats covers ground fast for the accommodation and amount of power. Making long daily runs possible.

Boats with more beam and wider entries as the bow will tend to bounce around a lot more, kick more spray up and pound and wallow when heading into waves.

The fine bow here gives excellent behaviour for when the waves are close together, even if they are quite tall.

In circumstances when the wavelength is longer than the boat the boat will travel up the face then launch itself into midair and land with an enormous slam when the flat bottom meets the water.  But in their natural environment of rivers, lakes and estuaries the hullform works very nicely indeed.

Interior of Canal boat or DAyboat Launch Picnic boat you can build yourself. 10hp high thrust outboard. Sleep or camp cruiser: storerboatplans.com
DAyboat Launch Picnic boat you can build yourself. 10hp high thrust outboard. Sleep or camp cruiser: storerboatplans.com

With the Dayboat/Launch its length of 23ft (7m) would necessitate a beam of less than 5ft (1.5m) which would make the boat somewhat unstable and one of the design criteria was for a central table with seating around (Picnic Boat).  The solution (which I was a bit hesitant about at first) was to effectively have the bow of a longer boat but cut it off at the stern.  As you can see from the plan view above the riverboat is all bow.

The Risks of boat designs that are “All Bow”

Boats that are “all bow” often have reputations as wild steerers in a following sea.  The stern has so much volume that when a wave comes up from behind it floats up suddenly. This tends to thrust the bow deep into the back of the wave in front.

This is the secret of the nice rough water handling of narrow sterned boats. Neither the bow nor the stern overpowers the other so the boat remains in balance in rough sea conditions.

My thought was that Sydney Harbour can get choppy at times. But the waves are generally quite closely spaced. The scenario of either going up the faces and launching into midair or burying the bow were fairly unlikely.

We wanted some ability to handle waves, so this was considered adequate for when canal boats or river boats have to cross larger lakes. The high speed can help of course by helping to keep the time of exposure down

Interior Arrangements – think camp aboard:

There are many possible options. There are big advantages in building speed because of the prefabricated plywood panels. So to throw it away with a complex interior would be a mistake. More camp aboard, although a separate WC was considered essential

The original is shown in the drawing above,  The cuddy cabin was for lockable storage and a porta potti, which is a great thing to have aboard a picnic boat!  A few nice wines or beers and …

Dayboat Launch Pop and I at Goolwa South Australia: a camp aboard canal boat riverboat: storerboatplans.com

“Pop&I”, built by a father and son team some distance up the Murray River, was changed considerably but still very much camp aboard. The  outboard was moved from a well to in a notch just in front of the transom.  It has a settee/double berth in the aft end of the cabin.

And seating on the starboard side has been replaced with a galley. Really a cupboard a spirit stove can sit on top of. And a cutout for a bucket as a sink.

The canopy has been run through to the stern and up to the back of the foredeck.  A windscreen has been fitted.

Rules for a simple and light interior that won’t require too much labour.

The do’s and don’ts of the interior include
1/ You can’t go up any higher
2/ The cabin has to be light.
3/ The seats, galley etc has to be bonded to the sides of the riverboat. The interior components support the sides of the hull.

DAyboat Launch Picnic boat you can build yourself. 10hp high thrust outboard. Sleep or camp cruiser: storerboatplans.com

And Stephen Foster’s reworking with a very light cabin structure It has a double berth forward, but the rest of the boat is much more camp aboard

Stephen Foster's wonderful execution on Sydney Harbour. 23ft dayboat/launch; storerboatplans.com

Modest Outboard Powering with good performance of these Dayboats/Canal boats :

With the 9.9hp six knots is about top speed, though there are some pics of Pop&I whizzing along a bit faster than that when floating light just after first launch.  But that is not the purpose of these boats – keep the speed down, save fuel and have a comfortable ride (the faster you go the more it will pound as the boat will lift and present more of the flat bottom to the waves.)

Here is Stephen’s Dayboat Launch on launching day. When these riverboats are light they have surprising speed. But most riverboats and canal boats are not intended to go this quickly. Around 8 knots is fine.

23ft Dayboat Launch on Hawkesbury River. Planing!? storerboatplans.com

We would probably recommend a 4-stroke outboard because of the slower speed and greater weight.  One of the high thrust models would work very well.

Stress! Going into Survey as a Hire and Drive boat:

For its original use as a Hire and Drive vessel, the dayboat had to be put into Survey.  I was quite worried that anything this unconventional would have trouble getting past the powers-that-be.

Of particular concern was the criterion that the boat not capsize with the crew on board. Not only that but whole six (6) of its crew standing on one edge of the boat.  Once I worked out the centre of gravity of the whole shebang I fed it into the computer.

The result was that in theory boat was just short of enough stability.  So a lead shoe of 200kg was added to the drawing, which was enough to make her pass.

The Survey Team (of 4!) check out the Dayboat/Launch

Richard decided that he wasn’t going to fit the lead unless absolutely necessary.

So when the boat was finished it was whacked in the water and the Survey blokes called in.  Four of them arrived on the appointed day in matching spotless white overalls.  They jumped aboard and started filling out checklists and the like.  Richard asked them what they thought of the stability for six.

Reply was “Six? Mate … she’ll handle Eight easy”.

So much for my hours of working out the weight for each component of the boat so I could locate the height and longitudinal position of the centre of gravity!

Several have been launched and their owners are quite happy with them.  Not a bad machine at all (if I do say so myself).

23ft Dayboat Launch on Hawkesbury River

Materials list for Dayboat/Launch (PDF File)
One Alternative Interior Layout (html)