Finally I finished the plan for the new OzRacer RV. It is a much simpler build of the original OzRacer concept so will be very attractive to people looking for a first boat. Plans are still the old $20 but even more detail than before. Order the plans for the simple and cheap OzRacer RV read more →
Cliff and PJ live in Warm Queensland and Wintry Tasmania. However they both like to go the the yearly (June) wooden boat festival in tropical Far North Queensland.
This year they decided to build one of my Quick Canoes. They started on Saturday and finished including putting the canoe on the car roof by the following thursday.
They are experienced woodworkers so added some very nice details.
Melanie in the UK wrote to me. She has just bought an old Mirror dinghy and started sailing for the first time.
Problem is that the boat leaks and she doesn’t want to stop using the boat until the end of the season.
I have a philosophy of keeping older boats on the water and not pulling them off for months on end until you have the time to do the job.
So the article here is useful to see what can be done with an old leaky plywood sailing dinghy to keep it going.
It is perfect sailing weather at the moment in the UK and it is better she is out there learning but with the worst of the leaks gone.
With a disciplined approach she should be able to get all of this done in a week or so. The general leaks fixed permanently and the rotted area reinforced so that the boat won’t break.
This is the second of my talks in the USA. It focuses a bit more on construction and some of the methods that can be used to keep a boat light and simple, but very strong and stiff.
It also discusses how there is a “creep” in boatbuilding and design that increases the weight of boats way over what is really needed for a strong structure.
There are huge advantages in keeping the epoxy at a slightly raised temperature. * It flows out better onto the work * It mixes easier * The curing kicks off faster in cold weather (and the box can easily only be turned on when needed. There are huge advantages in keeping the epoxy at a read more → This is a problem most of use come up against at least once. However it is unlikely to happen a second time. Richard wrote to me asking why his epoxy was still soft 3 days later. He suggested it might be because of one of: 1. The immediate guess is that it’s been too cold read more → There are a number of labour and materials saving techniques that are applicable when using epoxy. Contents of this section Wet-on-Wet Coating and Dewaxing Cured Epoxy. Building strong lightweight boats – a note on the use of epoxy One Hit coating and gluing Wet-on-Wet Coating and Dewaxing Cured Epoxy. As epoxy cures some of the read more →
Where a seam has to be glassed and it is difficult to make the glass sit flat because of a complex curve then a double bias tape is used. It is also useful for complex 3D curves like the tips of centreboards and rudders. Commercial double bias tapes can be bought but you can make read more →
This is the normal method for fibreglassing small areas – typically using fibreglass tape to hull seams. Here I document the process of coating the hull and glasstaping the chines in one hit. Integration of different steps in this way is one of the major efficiencies of modern epoxy boatbuilding. However if simply glass taping read more →
Howdy, I have just updated my FAQ with some “How To” sections on different methods of using fiberglass. Storerboatplans FAQ It covers the different methods for small areas and large areas and also a method for getting glass to lie flat over complex curved surfaces. There are good photos for some of the sections to read more →
Well, I’ve just had a big day up at Duck Flat Wooden Boats doing some work on the 3 PDRacers they are building for the nationals at Goolwa in March. I’m not the only person working on them. Robin Badenoch has been in and more or less finished the masts and is on his way read more →
At the moment I am in Sydney for a couple of weeks. Not a lot of boating stuff happening apart from work I’m doing on developing a lighter mast and tabernacle (so the mast will swing up into position easily) for a San Francisco Bay Pelican. But the main point of this post is to read more →
I was asked by the people at Duck Flat Wooden Boats whether I would be interested in teaching at their Spring School. It is their first one for a few years and has the purpose of “getting people excited about boatbuilding”. I must admit that was pretty well how it went. 12 different projects and read more →
I have just added another page to my site. A couple of keen canoists lightweighted my already light Eureka 155 Canoe. The end result was that this 15ft 6″ boat came in at 34lbs (15.5kg). Note the neat and very lightweight seat made of a washing line. It is important when drilling the holes to read more →
English